- Talktalk Hg633 Firmware
- Huawei Hg633 Firmware Update Download
- Firmware For Huawei Hg633 Router 2019
- Huawei Hg633 Update
Not supported
- This is an example to configure the switch: numbers 0-2 will be lan, labeled as Ports LAN1X, LAN2X, LAN3X on the unit, number 3 (LAN4X) will be the Internet (WAN), 8 is the internal connection to the router itself.Don't be fooled: vlan1 = eth0.1, vlan2 = eth0.2 and so on.
- Thank you for this. I am trying to do the same as you. I currently have my main router as 192.168.1.1 and i have set the IP address of the Huawei HG633 (access point) as 192.168.1.3. When I get to STEP 4, it doesnt accept the Default Gateway. I put in 192.168.1.1 as the SOURCE IP ADDRESS and 255.255.255.0 as the OURCE SUBNET MASK.
Firmware For Huawei Hg633 Router 2019 Chunking Express Torrent Vortex Cloud Gaming Hack Download Santiago Munez Nationality How To Bend In 3ds Max Software Generator Paypal 2019 For Windows 7 Crack Rose Riddle 2 Werewolf Shadow Placa Qualcomm Atheros Ar9485 802.11bgn Monster High New Ghoul In School Wii Iso.
Forum: https://forum.openwrt.org/viewtopic.php?id=55856
Source code: hg635-opensource.tar.gz
Installation
Flashing ANY Firmware
You must set your TCP/IP v4 protocol at your computer to:
- Netmask: 255.255.255.0
- DNS: (optional, can be blank).
Then:
- Press reset button near the antenna.
- Keep it pressed while powering up during ~20+ seconds.
- Acces to http://192.168.1.1 and upload binary file.
Specific Configuration
Interfaces
The default network configuration is:
| Interface Name | Description | Default configuration |
|---|---|---|
| br-lan | LAN & WiFi | 192.168.1.1/24 |
| eth0.1 | LAN ports (1 to 4) | bridged |
| eth0.2 | WAN port (WAN) | nat (WAN) |
| wlan0 | WiFi | bridged (disabled) |
| wlan1 | WiFi | bridged (disabled) |
Switch Ports (for VLANs)
Talktalk Hg633 Firmware
This is an example to configure the switch: numbers 0-2 will be lan, labeled as Ports LAN1X, LAN2X, LAN3X on the unit, number 3 (LAN4X) will be the Internet (WAN), 8 is the internal connection to the router itself. Don't be fooled: vlan1 = eth0.1, vlan2 = eth0.2 and so on.
| Port | Switch port | Mode |
|---|---|---|
| 1 | 0 | lan |
| 2 | 1 | lan |
| 3 | 2 | lan |
| 4 | 3 | lan |
| WAN | 4 | Internet (WAN) |
| n/a | 5t | to CPU |
Hardware
Info
Huawei Hg633 Firmware Update Download
| Instruction set | MIPS |
|---|---|
| Vendor | Broadcom |
| bootloader | cfe |
| Board ID | |
| System-On-Chip | Broadcom BCM63168 |
| CPU @Frq | BMIPS4350 V8.0 @ 400 MHz |
| Flash-Chip | NAND |
| Flash size | 128MB |
| RAM-Chip | DDR2-800 |
| RAM size | 128MB |
| Wireless | BCM4350 ac/a/b/g/n (onboard) + BCM6362 b/g/n (SoC) |
| Ethernet | BCM53124, 5x 1000M |
| USB | 1x 2.0 |
| Serial | Yes |
| JTAG | ? |
Photos
Opening the case
Note: This will void your warranty!
Main PCB:
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
N/A
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
Serial port settings 115200, 8N1
Pinout:
J5002
1 - RXD
2 -
3 - Probably VCC (3V3)
4 - GND
5 - TXD
Photo of PCB with markings
GPIO
LEDs
Read: System configuration: Leds to configure the leds
Buttons
→ hardware.button on howto use and configure the hardware button(s).
Bootlogs
OEM Bootlog
HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS STRF 400H PHYE DDR3 SIZ4 SIZ3 SIZ2 DINT USYN LSYN MFAS LMBE RACE PASS ---- ZBSS CODE DATA L12F MAIN CFE version 1.0.38-114.174 for BCM963268 (32bit,SP,BE)Build Date: Sat Nov 9 13:59:00 CST 2013 (l00184769@localhost)Copyright (C) 2000-2011 Broadcom Corporation.NAND flash device: name , id 0x98d1 block 128KB size 131072KBExternal switch id = 53125 Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 134217728 bytes (128MB) Boot Address: 0xb8000000